Ultimate Passage Discount Marine Electronics
Call: 440-617-0025 (Ohio)
or QUESTIONS Via Email?  CLICK HERE!


  • Manufacturer
  • Category
  • What's ON SALE!
  • REBATE Items
  • Site Map
  •  Garmin
  •  Raymarine
  •  Lowrance
  •  Jabsco
  •  Motorguide
  •  Taco Down Riggers
  •  Xantrex
  •  ALL Navionics --OR:
  • Navionics "MSD" Format - Lowrance, Humminbird, Raymarine, Simrad

  • "CF" Format for older units PRE-2012
  •  C-Map
     Garmin Mapping
     Humminbird Charts
     Lowrance Insight
     Fishing Hot Spots
  • CONTACT US:
  • 440-617-0025 (Ohio)
    Monday-Thursday
    9am to 5pm
    Fridays until 3pm
    EASTERN TIME
    or
    via EMAIL Now!
  • Our Address:
    3399 Balsam Drive
    Westlake, OH 44145
    Note: NO RETURNS Accepted Here!
    Call/Email for an RMA.
  • Our Return Policy

  • Category: Hardware

    PSS SHAFT SEAL 1-3/4" SHAFT 3-1/4" TUBE

    ** PSS Shaft Seal Part Number - 02-134-314 **

    Our SKU# - 50858
    PSS SHAFT SEAL 1-3/4" SHAFT 3-1/4" TUBE
    Click Here for Larger Image
    PSS Shaft Seal 1-¾" Shaft 3-¼" Tube
    PSS Shaft Seal Part Number:02-134-314
    MSRP/Retail Price:$490.00
    Minimum Ad Price: 392.00$ More Info In Cart
    In Stock? NOT IN STOCK
    ETA: Usually Ships in 3-10 Days
    PRE-ORDER!
    Condition: BRAND NEW
    from PSS Shaft Seal

    (NOT a "Refurb" or "Reman"!)
    Related Items & Accessories
    are shown below...


    PSS Shaft Seal 1-¾" Shaft 3-¼" Tube 02-134-314:

    PSS Shaft Seal 1-3/4" Shaft 3-1/4" Tube

    Shaft Diameter: 1-3/4"
    Stern Tube Diameter (D): 3-1/4" to 3-3/8"
    Total Length (A): 9.175"
    Total Length (compressed) (Compressed A): 8.175"
    Rotor Diameter (B): 3.75"
    Carbon Cuff Diameter (C): 3.25"
    Stern Cuff Length (E): 2"

    The PSS Shaft Seal is the number one selling marine mechanical seal
    worldwide and is installed as standard equipment by many of the worlds most
    reputable boat builders / yards. The PSS Shaft Seal is also recognized as
    the premiere retrofit (aftermarket) seal on the world market. Certified by
    Bureau Veritas, ABS & Rina: Boat builders / yards recognize the advantages
    and value of installing the PSS as it eliminates the maintenance, constant
    adjustment & cost associated with traditional packing type glands. Aside
    from these benefits, the PSS Shaft Seal helps to eliminate water in the
    bilge (100% water tight) & wear to the propeller shaft. The PSS Shaft Seal
    can be easily retrofitted and is available for shafts ranging from 3/4"
    (20mm) to 6" (150mm).

    The PSS Shaft Seal is a mechanical face seal that is created between
    the flat surfaces of the rotating stainless steel rotor and the stationary
    carbon flange. The stationary carbon flange is attached to the vessels stern tube with hose clamps and the carbon flange is attached to the front side of the bellows with hose clamps. The stainless steel rotor is fit on the shaft
    in front of the carbon flange. The stainless steel rotor is used to compress the bellows before the collar is secured to the shaft with set-screws. This
    compression (pre-load) maintains contact between the faces and allows the
    PSS to compensate for the thrust from the propeller. The carbon flange is
    bored larger than the shaft diameter allowing it to "float" around the shaft and thus compensate for most misalignment and vibration problems. The
    stainless steel collar is sealed to the shaft by two o-rings that are
    recessed into the bore of the collar. These o-rings rotate with the shaft
    and stainless steel rotor and do not experience wear during operation.


    **As with any rubber hose below waterline, the PSS bellows must be inspected on a regular basis for any sign of wear, aging or chemical deterioration.
    PYI suggests as preventative maintenance that the PSS bellow be replaced in
    six year intervals. During bellows replacement it is recommended the o-rings & set screws in the stainless steel rotor also be replaced."

    Bellows may need to be more frequently inspected in an environment where
    non-sealed batteries emit sulfuric acid. Sulfuric acid vapor will accelerate rubber deterioration, as will an ozonater.

    The Maintenance Kit includes the items you need to properly maintain your
    PSS Shaft Seal. Included in the kit is one (1) PSS bellow, two (2) O-rings,
    five (5) set screws, four (4) new hose clamps and an allen key.
    Quantity:
    Retail Price: $490.00 Not in stock
    ETA: Usually Ships in 3-10 Days
    Pre-Order!

     Related Items
    PSS SHAFT SEAL MAINTENANCE KIT 1 3/4" SHAFT 3 1/4" TUBE
    MFG#: 07-134-314R
    PSS SHAFT SEAL MAINTENANCE KIT 1 3/4
    More Info
    Click "BUY NOW" For
    OUR SELLING PRICE!
    Quantity on Hand: 1
    buy now